Hướng dẫn sử dụng DeWalt 28-682 Saw

Hướng dẫn sử dụng cho thiết bị DeWalt 28-682 Saw

Hướng dẫn sử dụng DeWalt 28-682 Saw

Trích xuất nội dung

Nội dung tóm tắt trên trang số 1

(Model 28-682)PART NO. 911988 - 07-28-04Copyright © 2004 Delta MachineryTo learn more about DELTA MACHINERYvisit our website at: www.deltamachinery.com.For Parts, Service, Warranty or other Assistance,please call1-800-223-7278 (In Canada call 1-800-463-3582).INSTRUCTION MANUAL18" Band Saw

Nội dung tóm tắt trên trang số 2

TABLE OF CONTENTSIMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4ADDITIONAL SPECI

Nội dung tóm tắt trên trang số 3

SAFETY GUIDELINES - DEFINITIONSIt is important for you to read and understand this manual. The information it contains relates to protecting YOURSAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.Indicates a potentially hazardous situation

Nội dung tóm tắt trên trang số 4

GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,fire, and/or serious personal injury or property damage.IMPORTANT SAFETY INSTRUCTIONS1. FOR YOUR OWN SAFETY, READ THE INSTRUCTIONMANUAL BEFORE OPERATING THE MACHINE.Learning the machine’s application, limitations, andspecific hazards will greatly minimize the possibility ofaccidents and injury.2. WEAR EYE PROTE

Nội dung tóm tắt trên trang số 5

ADDITIONAL SAFETY RULES FOR BAND SAWSFAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.1.2.3.4.5.6.7.8.9.10.11.12.13.DO NOT OPERATE THIS MACHINE UNTIL it isassembled and installed according to theinstructions.OBTAIN ADVICE from your supervisor,instructor, or another qualified person if you arenot familiar with the operation of this tool.FOLLOW ALL WIRING CODES and recommendedelectrical connections.USE THE GUARDS WHENEVER POSSIBLE. Checkto see that they are in place, properly ad

Nội dung tóm tắt trên trang số 6

POWER CONNECTIONSA separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting themachine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is ofthe same ch

Nội dung tóm tắt trên trang số 7

3. Grounded, cord-connected machines intended foruse on a supply circuit having a nominal ratingbetween 150 - 250 volts, inclusive:GROUNDED OUTLET BOXCURRENTCARRYINGPRONGSIf the machine is intended for use on a circuit that has anoutlet that looks like the one illustrated in Fig. C, themachine will have a grounding plug that looks like theplug illustrated in Fig. C. Make sure the machine isconnected to an outlet having the same configuration asthe plug. No adapter is available or should be used

Nội dung tóm tắt trên trang số 8

FUNCTIONAL DESCRIPTIONFOREWORDDelta Model 28-682 is an 18" Wood Cutting Band Saw. This machine has speeds of 2300 and 3250 SFPM (surface feetper minute). Its blade to frame capacity is 171/2" and its height under guide capacity is 12". The band saw has a quickblade tensioning mechanism for ease of changing blades. The Delta Model 28-682 has a large 173/4"x18" cast iron tablethat can be tilted 48 degrees to the right and 10 degrees to the left. The band saw also comes with a 4" O.D. dust portfor

Nội dung tóm tắt trên trang số 9

UNPACKING AND CLEANINGCarefully unpack the machine and all loose items fromthe shipping container(s). Remove the protective coatingfrom all unpainted surfaces. This coating may be removedwith a soft cloth moistened with kerosene. (Do not useacetone, gasoline or lacquer thinner for this purpose.) Aftercleaning, cover the unpainted surfaces with a good qualityhousehold floor paste wax.1.2.BARemove the four bolts (A) Fig. 1 (three of which areshown) that attach the saw (B) to the shipping skid.ASav

Nội dung tóm tắt trên trang số 10

TABLE1.2.Remove the table pin (A) Fig. 5.Align the blade with the table slot (B) Fig. 5. Slide the table until the blade has reached the center cutout (C) Fig.5, then rotate the table 90 degrees toward the front of the machine.NOTE: Make sure that the table slot (B) Fig. 6 is facing toward the right of the machine.3. Align the two table studs (A) Fig. 6, in the bottom of the table, with the two holes in the trunnion assemblies.4. Thread the trunnion lock knob (D) Fig. 7 onto the table stud. Repe

Nội dung tóm tắt trên trang số 11

FENCE1. Align the two holes (A) Fig. 9 in the front fence rail with the two holes (B) in the front of the table.NOTE: Make sure that the scale on the front fence rail is facing upward.2. Insert a 1/4-20 x 1-1/2" socket-head cap screw through one of the holes (A) Fig. 9 hole in the front fence rail. Placea spacer on the screw between the front fence rail and the table. Thread the screw into the front of the table. Repeatfor the other hole (A) in the front fence rail. Tighten the two screws secure

Nội dung tóm tắt trên trang số 12

OPERATIONOPERATIONAL CONTROLS AND ADJUSTMENTSSTARTING AND STOPPING SAWThe power switch is located on the left side of the machine. To turn the machine “ON”, push the green start button (A)Fig. 14. To turn the machine “OFF”, push the red stop button (B).LOCKING SWITCH IN THE “OFF” POSITIONIMPORTANT: When the tool is not in use, the switch should be locked in the “OFF” position to prevent unauthorizeduse, using a padlock (C) Fig. 15 with a 3/16" diameter shackle.ACBFig. 14Fig. 15TI

Nội dung tóm tắt trên trang số 13

4.Raise the blade tension lever to the “up” positionand turn it clockwise to increase tension or counterclockwise to relieve the tension.5. After the first turn, lower the blade tension lever andcheck the tension scale. If the tension is still notcorrect, repeat the procedure.The tension scale is correct for standard bladesused on average work. Although you may rely on thefeel or tone of the blade, Delta recommends thatyou use the tension scale to avoid blade breakageby applying too much or

Nội dung tóm tắt trên trang số 14

CHANGING SPEEDSDISCONNECT MACHINE FROM POWER SOURCE.1.2.3.4.5.Open the bottom access door (See D, Fig. 26).Locate and loosen motor release handle (C) Fig. 20Ainset by turning it counter-clockwise.Lift up motor assembly and move belt (A) to desiredgroove on motor pulley (B). Move belt to outer groove(D) for 2300 SFPM, or to inner groove (E) for 3250SFPM.Push down on motor assembly and then turn motorrelease handle (C) clockwise to tighten belt.Close the bottom access door.ECDABFig. 20AADJUSTING U

Nội dung tóm tắt trên trang số 15

ADJUSTING THE TABLE POSITIVE STOPADISCONNECT MACHINE FROM POWERSOURCE.This machine is equipped with a positive stop thatallows the table to be rapidly positioned at 90 degrees tothe blade after the table has been tilted.To check and adjust:1. Place the table in the 90 degree position and lock itin place.2. Place a square (A) Fig. 24 on the table with one endagainst the blade to check for 90 degrees.3. If an adjustment is necessary, loosen the locknut (B)Fig. 25 and tighten or loosen the adjustin

Nội dung tóm tắt trên trang số 16

AAFig. 28Fig. 28AADJUSTING RESAW GAUGEThe resaw gauge (A) attaches to the fence (Fig. 28). Slide it along the fence slot until the edge is slightly in front of theblade teeth. Use this gauge for resawing operations and for cutting warped workpieces.ADJUSTING BELT TENSIONIf it becomes necessary to adjust the belt tension on the machine, turn the motor release handle (A) Fig. 28A counterclockwise. Lower or raise the motor, and when adjustment is complete, tighten the motor release handle (A).DUST

Nội dung tóm tắt trên trang số 17

BAND SAW BLADESA band saw blade is a delicate piece of steel that is subjected to tremendous strain. You can obtain long use from aband saw blade if you use it properly. Be sure you use blades of the proper thickness, width and temper for the varioustypes of material and cuts.Always use the widest blade possible. Use narrow blades only for sawing small, abrupt curves and for fine, delicatework. This will save blades and1 will produce better cuts. For cutting wood and similar materials, Delta off

Nội dung tóm tắt trên trang số 18

Trouble: BAND SAW VIBRATES EXCESSIVELY.Probable Cause1. Machine not mounted securely to stand.2. Stand on uneven surface.3. Worn belt.4. Pulley not aligned.5. Motor not fastened securely.Remedy1. Tighten all mounting hardware.2. Reposition on flat level surface.3. Replace belt.4. Adjust pulleys.5. Tighten all mounting hardware.Trouble: BAND SAW DOES NOT COME UP TO SPEED.Probable Cause1. Low voltage due to improper extension cord size.2. Low voltage.Remedy1. Replace with adequate size cord.2. Con

Nội dung tóm tắt trên trang số 19

MAINTENANCEKEEP MACHINE CLEANLUBRICATIONPeriodically blow out all air passages with dry compressedair. All plastic parts should be cleaned with a soft dampcloth. NEVER use solvents to clean plastic parts. They couldpossibly dissolve or otherwise damage the material.Apply household floor paste wax to the machine table andextension table or other work surface weekly.PROTECTING CAST IRON FROM RUSTTo clean and protect cast iron tables from rust, you willneed the following materials: 1 pushblock from

Nội dung tóm tắt trên trang số 20

PORTER-CABLE • DELTA SERVICE CENTERS(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)Parts and Repair Service for Porter-Cable • Delta Machinery are Available at These Locations(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta)ARIZONATempe 85282 (Phoenix)2400 West Southern AvenueSuite 105Phone: (602) 437-1200Fax: (602) 437-2200CALIFORNIAOntario 91761 (Los Angeles)3949A East Guasti RoadPhone: (909) 390-5555Fax: (909) 390-5554Tampa 33

ĐỂ LẠI MỘT BÌNH LUẬN